DC电源插座
小型迷你DC直流插座 DC电源插座直径为3.4mm，直径为1.0mm / 1.3mm的针孔
2016-10-12 11:55:42
型号 : TDC-022 series
品牌 : 瑞丰开关Switch Jack SerieS

Specification

  1. Rating : 2A/16V DC Max

  2. Contact resistance : Contact resistance shall be less than 50 Milliohms at initial and 100 Milliohms after life test between a terminal of the socket and that of the mating plug; less than 30 Milliohms at initial and 60 Milliohms after life test between terminal of the socket in a closed circuited, when measured at a current of less than 100 Milliampere 1 KHz. The Mating plug use shall be cleaned and free from oxidation film of the surface.

  3. Insulation resistance : Insulation resistance between insulated metal parts shall be 100 Megohm or more at initial and 50 Megohm or more after cold test, hot test, and humidity test when measured with a 500 volts D. C. insulation resistance meter.

  4. Insertion and Withdrawal Force The insertion and withdrawal force shall be 0.3 – 3Kgs at initial and 0.2 – 2Kgs after life test with the gauge plug.

  5. Terminal Strength The terminal shall be capable of withstanding a force of 500 Gram applied in any directions for 10 second without loosing and breakdown.

  6. life test : 5,000 cycles

 
Features
The mating plug shall be in 3.4mm diameter with 1.0mm/1.3mm diameter pin hole. 
 
Material
Shunt Terminal : Brass, Tin plated Tip Terminal : Copper Alloy, in plated Ground Terminal : Brass, Tin plated Plastic Housing : PA66 
Specification

  1. Rating : 2A/16V DC Max

  2. Contact resistance : Contact resistance shall be less than 50 Milliohms at initial and 100 Milliohms after life test between a terminal of the socket and that of the mating plug; less than 30 Milliohms at initial and 60 Milliohms after life test between terminal of the socket in a closed circuited, when measured at a current of less than 100 Milliampere 1 KHz. The Mating plug use shall be cleaned and free from oxidation film of the surface.

  3. Insulation resistance : Insulation resistance between insulated metal parts shall be 100 Megohm or more at initial and 50 Megohm or more after cold test, hot test, and humidity test when measured with a 500 volts D. C. insulation resistance meter.

  4. Insertion and Withdrawal Force The insertion and withdrawal force shall be 0.3 – 3Kgs at initial and 0.2 – 2Kgs after life test with the gauge plug.

  5. Terminal Strength The terminal shall be capable of withstanding a force of 500 Gram applied in any directions for 10 second without loosing and breakdown.

  6. life test : 10,000 cycles

 
Features
The mating plug shall be in 3.4mm diameter with 1.0mm/1.3mm diameter pin hole. 
 
Material
Shunt Terminal : Brass, Tin plated Tip Terminal : Copper Alloy, in plated Ground Terminal : Brass, Tin plated Plastic Housing : PA66 
 
 
规范
 
额定值：2A / 16V DC最大
 
接触电阻：在插座的端子和配合插头的端子之间，接触电阻在初始时小于50毫欧，在寿命测试后小于100毫欧;当在小于100毫安1KHz的电流下测量时，在闭合电路中的插座的端子之间，在初始时小于30毫欧姆和在寿命测试之后为60毫欧姆。配接插头应使用
清洁并且没有表面的氧化膜。
 
绝缘电阻：绝缘金属部件之间的绝缘电阻在初始时应为100兆欧以上，而在用500伏直流绝缘电阻表测量时的冷试验，热试验和湿度试验后，绝缘电阻应为50兆欧以上。
 
插入和拔出力
插拔力在初始时为0.3〜3Kgs，寿命试验后为0.2〜2Kgs
与量规插头。
 
终端强度
该终端须能承受在任何方向施加的500克力
10秒，没有松动和故障。
 
寿命试验：10,000次循环
 
 
 
特征
 
配合插头应为直径为3.4mm，直径为1.0mm / 1.3mm的针孔。
 
材料
 
分流端子：黄铜，镀锡
尖端端子：铜合金，镀
接地端子：黄铜，镀锡
塑料外壳：PA66

 

网站首页