3.5mm耳机插座
3.5贴片式沉板耳机插座 3.5mm贴片立体声插孔 3.5mm SMD Stereo Jack
2016-10-11 15:24:26
型号 : TSH-509DS
品牌 : 瑞丰开关Switch Jack SerieS
Description
3.5mm SMD Stereo Jack
Specification
1.Rating : 1A/12V DC Max.
2.Contact resistance: Contact resistance shall be less than 50 Milliohms at initial and 100 Milliohms after life test between a terminal of the socket and that of the mating plug; less than 30 Milliohms at initial and 60 Milliohms after life test between terminal of the socket in a closed circuited, when measured at a current of less than 100 Milliampere 1 KHz. The Mating plug use shall be
cleaned and free from oxidation film of the surface.
3.Insulation Resistance
Insulation resistance between insulated metal parts shall be 100 Megohm or more at initial and
50 Megohm or more after cold test, hot test, and humidity test when measured with a 500 volts
D. C. insulation resistance meter.
4.Insertion and Withdrawal Force
The insertion and withdrawal force shall be 0.3 – 3Kgs at initial and 0.2 – 2Kgs after life test
with the gauge plug.
5.Terminal Strength
The terminal shall be capable of withstanding a force of 500 Gram applied in any directions for
10 second without loosing and breakdown..
6.life test : 10,000 cycles
Features
The Mating plug shall be in 3.5mm diameter.
Material
Plastic Housing : PA6T
Terminal 1 : Copper Alloy, Gold Flash
Terminal 2 : Copper Alloy, Gold Flash
Terminal 3 : Copper Alloy, Gold Flash
Terminal 4 : Copper Alloy, Gold Flash
Terminal 5 : Copper Alloy, Gold Flash
Shield : Copper Alloy, Nickel Plated
Bushing : Brass, Nickel Plated
描述
3.5mm贴片立体声插孔
规范
1.额定值：1A / 12V DC最大。
2.接触电阻：在插座的端子和配合插头的端子之间，接触电阻在初始时小于50毫欧，在寿命测试后小于100毫欧;当在小于100毫安1KHz的电流下测量时，在闭合电路中的插座的端子之间，在初始时小于30毫欧姆和在寿命测试之后为60毫欧姆。配接插头应使用
清洁并且没有表面的氧化膜。
3.绝缘电阻
绝缘金属部件之间的绝缘电阻在初始时应为100兆欧姆或更多
冷试验，热试验和湿度试验后，用500伏电压测定时，为50兆欧姆以上
绝缘电阻计。
4.插入和拔出力
插拔力在初始时为0.3〜3Kgs，寿命试验后为0.2〜2Kgs
与量规插头。
终末强度
该终端须能承受在任何方向施加的500克力
10秒没有松动和故障..
6.寿命试验：10,000次循环
特征
配合插头应为3.5mm直径。
材料
塑料外壳：PA6T
端子1：铜合金，黄金闪光
端子2：铜合金，黄金闪光
端子3：铜合金，黄金闪光
端子4：铜合金，黄金闪光
端子5：铜合金，黄金闪光
屏蔽：铜合金，镀镍
衬套：黄铜，镀镍