瑞丰五金制品（东莞）有限公司Rui Feng hardware products (Dongguan) Co., Ltd |
文件编号 |
RF-SLIDE SWITCH |
|||||||||||||||||||
|
发布日期 |
2018年1月8日 |
||||||||||||||||||||
|
SPECIFICATION 规格书 |
第 A 版 |
第1页 共3页 |
|||||||||||||||||||
|
MODEL NO. 产品名称：拨动开关 滑动开关 拨码开关 |
|||||||||||||||||||||
|
DRAWN制订 |
刘工 |
APPD.审核 |
戴海明 |
||||||||||||||||||
|
1、RATING （额定值） ：0.5A 1A 3A 6A 12V 20V 50V DC 120V 125V 250V AC |
|||||||||||||||||||||
|
2、FUNCTION （接触型式） ：1P1T 2P2T 2P2T 3P3T 3P1T 4P1T 4P2T 3P2T 4P2T 5P2T |
|||||||||||||||||||||
|
3、TIMING （时间特性） ：NON-SHORTING |
|||||||||||||||||||||
|
4、ELECTRICAL CHARACTERISTICS（电气性能规格） ： |
|||||||||||||||||||||
|
ITEM项目 |
TEST CONDITIONS测试条件 |
PERFORMANCE规格 |
|||||||||||||||||||
|
4.1 |
CONTACT RESISTANCE 接触电阻 |
MEASURED AT SMALL CURRENT(100mA OR LESS) 在微小电流(100mA)以下测试. |
100mΩMAX. 100毫欧以下.
|
||||||||||||||||||
|
4.2 |
INSULATION RESISTANCE 绝缘电阻 |
APPLY A VOLTAGE OF 500V DC FOR 1 MIN. TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE. (1) BETWEEN BODY AND TERMINAL。 (2) BETWEEN TERMINALS。 输入500V DC 电压1分钟,按以下接触方法测试: (1) 外壳与排脚之间。 (2) 端子之间。 |
100MΩMIN. 100兆欧以上.
|
||||||||||||||||||
|
4.3 |
DIELECTRIC STRENGTH 耐电压 |
AC500V(50-60Hz)FOR 1 MIN TRIP CURRENT:0.5mA BETWEEN TERMINALS. BETWEEN INDIVIDUAL TERMINALS AND FRAME. 输入500V(50-60Hz)电压,1分钟感度电流为0.5mA,按以下接触方法测试: (1)排脚相互之间 (2)排脚与外壳之间. |
WITHOUT DAMAGETOPARTS ARCING OR BREAKDOWN ETC 没有绝缘破坏等异常 |
||||||||||||||||||
|
5、MECHANICAL CHARACTERISTICS (机械性能规格) |
|||||||||||||||||||||
|
ITEM项目 |
TEST CONDITIONS测试条件 |
PERFORMANCE规格 |
|||||||||||||||||||
|
5.1 |
OPERATING FORCE 作动力 |
MEASUREMENT SHALL BE MADE ST THE NEAREST POINTF OF THE COMPONENT OR AT THE POINT 3mm FROM THE TIP OF THE ACTUATOU(KNOB0 在距离胶柄3mm作测定点. |
250gf±100gf |
||||||||||||||||||
|
5.2 |
TERMINAL STRENGTH 端子强度 |
A STATIC LOAD OF(300gf)SHALL BE APPLIED TO THE TERMINAL FOR 15 SEC,IN ANY DIRECTON. 在排脚前端任意一个方向加(300gf)力度测试,时间为15秒. |
MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED WITHOUT LOOSENESS OF ACTUATOU. 在端子中没有裂开,松动等异常,满足于机械、电器性能。 |
||||||||||||||||||
|
5.3 |
DISPLACEMENT OF ACTUATOR (KNOB) 柄强度
|
A STATIC LOAD OF 10N(1Kgf)SHALL BE APPLIED TO THE TOP OF THE ACTUATOR(KNOB)AND THEN DESPLACEMENT SHALL BE MEASURED TO THE DIRECTION OF THE ARROW. 在柄的前端施加1Kgf的力度,位移应沿印记的方向上定. |
THE LEVER SHALL HAVE NO SERIOUS DEFORMATION AND FUNCTION IS NORMALLY. 柄部无严重变形,可以正常工作 |
||||||||||||||||||
瑞丰五金制品（东莞）有限公司Rui Feng hardware products (Dongguan) Co., Ltd |
文件编号 |
RF-SLIDE SWITCH |
|||||||||||||||||||
|
发布日期 |
2018年1月8日 |
||||||||||||||||||||
|
SPECIFICATION 规格书 |
第 A 版 |
第2页 共3页 |
|||||||||||||||||||
|
6、ENDURANCE CHARACTERISTICS (耐久性) : |
|||||||||||||||||||||
|
ITEM项目 |
TEST CONDITIONS测试条件 |
PERFORMANCE规格 |
|||||||||||||||||||
|
6.1 |
LIFE TEST 寿命试验 |
ENDURANCE WITHOUT LOADING： A SWITCH SHALL BE SUBJECTED TO 10,000 CYCLES AT A SPEED OF 15 TO 18 CYCLES PER MINUTE WITHORT LOADING. 无负荷: 在无负荷的条件下以每分钟15—18回的速度进行10,000次的测试. |
(1)CONTACT RESISTANCE(接触电阻) 200mΩ MAX.200毫欧以下. (2)INSULATION RESISTANCE(绝缘电阻) 50MΩ MIN. 50兆欧以上.. (3)WITHSTAND VOLTAGE(耐电压) AC 500V,1 MINUTE.AC 500V 1分钟 (4)OPERATING FORCE(作动力) ±30%INITIAL VALUE. 变化范围初始值±30% (5)WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. (测试后外表无损伤,并且满足机械性能) |
||||||||||||||||||
|
6.2 |
SOLDERA- BILITY TEST 可焊性试验 |
THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 240±5℃ FOR 3±0.5 SECONDS. 端子顶部被浸入锡焊池中2mm深,温度为 240±5℃,时间为3±0.5秒. |
(1)SOLDER WELTING TIME SHALLBE 3 SEC OR LESS. 焊接时间少于3秒 (2)THE AREA OF SOLDERING SHOULD BE OVER 95% 焊接面积要有95%以上. |
||||||||||||||||||
|
6.3 |
RESISTANCE TO SOLDERING HEAT TEST 耐焊性试验 |
(1).TEMPERATURE AND IMMERSING TIME 温度及浸锡时间
(2)IMMERSION DEPTH: IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD THICKNESS OF PRINTED WIRING BOARD 1.6mm. 浸锡深度： 浸锡深度至基板(PCB)表面，基板厚度为1.6mm.
|
WITHORT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTCS SHALL BE SATISFIED. 本体无变形,能满足于机械、电气性能。 |
||||||||||||||||||
|
6.4 |
COLD TEST 耐冷试验 |
THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -25±3℃ FOR 96 HOURS. THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置在温度-25±3℃中96小时后,再放置常温中1小时来进行测试. |
THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. 外观无异常,满足于机械、电气性能 |
||||||||||||||||||
瑞丰五金制品（东莞）有限公司Rui Feng hardware products (Dongguan) Co., Ltd |
文件编号 |
RF-SLIDE SWITCH |
|||||||||||||||||||
|
发布日期 |
2018年1月8日 |
||||||||||||||||||||
|
SPECIFICATION 规格书 |
第 A 版 |
第3页 共3页 |
|||||||||||||||||||
|
6.5 |
HEAT TEST 耐热试验 |
THE SWITCH SHALL BE STORED ATA TEMPERATURE OF70±2℃ FOR 96 HOURS. THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置在温度70±2℃中测试96小时后,再放置正常室温中1小时来测定.
|
THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. 外观无异常,满足于机械、电器性能. |
||||||||||||||||||
|
6.6 |
HUMIDITY TEST 潮湿试验 |
THE SWITCH SHALL BE STORED ATA TEMPERATURE OF 40±2℃ AND A HUMIFITY OF 90% TO 95% FOR 96 HOURS.THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置40±2℃的相对湿度为90%～95%环境中96小时后,再将样板放在正常环境1小时后进行测试.
|
|||||||||||||||||||
|
6.7 |
STANDARD ATMOSPHERE CONDITIONS 测试标准状态 |
UNLESS OTHERWISE SPECIFIED. THE STANDARD RANGE OF ATMOSPHERE CONDITIONS FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS: (1)AMBIENT TEMPERATURE:5℃ TO 35℃ (2)RELATIVE HUMIDITY:45% TO 85% (3)AIT PRESSURE :86Kpa TO 106Kpa 在没有指定的情况下测试温度、湿度、气压如下: (1)温度为5℃—35℃. (2)湿度为45%—85%. (3)气压为86Kpa—106Kpa.
|
|
||||||||||||||||||
|
6.8 |
PRACTICAL TEMPERATURE RANCE 使用温度范围 |
AT-16℃—+60℃. 在-16℃—+60℃内使用. |
|
||||||||||||||||||
